贝尔OLT命令

jierect

贝尔OLT业务配置手册
硬件配置
1、创建主控板
configure equipment slot nt-a planned-type fant-f   // 创建主控板NTA
configure equipment slot nt-b planned-type fant-f   //创建NTB
2、打开主控板主备倒换
configure equipment protection-group 1 admin-status unlock   
3、配置子框类型(基本类型)
configure system security profile admin slot-numbering type-based
configure system port-num-in-proto type-based
4、配置背板和LT板接口速率为10g
configure system max-lt-link-speed  link-speed ten-gb
保存配置数据
admin save
配置完背板速率以后必须要重启生效
admin equipment reboot-isam with-self-test
5、打开上联端口并设置速率(根据实际配置)
configure port nt-a:xfp:[1…4] no shutdown
configure port nt-a:xfp:[1…4] ethernet speed 1000
configure port nt-b:xfp:[1…4] no shutdown
configure port nt-b:xfp:[1…4] ethernet speed 1000
6、配置LT板
typ:isadmin>#configure equipment slot lt:1/1/[1…8] planned-type nglt-a

打开LT板的pon口:
typ:isadmin>#configure pon interface 1/1/1/[1…8] fec-dn disable admin-state up


ONU配置
7、上下行带宽模板（bandwidth/ shaper profile）
configure qos profiles bandwidth UPSTREAM_100M excessive-info-rate 100000 committed-info-rate 0 assured-info-rate 0 delay-tolerance 8
configure qos profiles shaper DOWNSTREAM_100M  committed-info-rate 0  committed-burst-size 0  excess-info-rate    100000  type singletokenbucketgpon
8、PQ Profile 模板 （ingress-qos）
configure qos profiles ingress-qos PQ0 dot1-p0-tc 0 dot1-p1-tc 0 dot1-p2-tc 0 dot1-p3-tc 0 dot1-p4-tc 0 dot1-p5-tc 0 dot1-p6-tc 0 dot1-p7-tc 0

9、创建SVLAN2000并绑定PQ  profile
//单层vlan
configure vlan id 2000 mode layer2-terminated in-qos-prof-name nameQ0
// 或用configure vlan id 2000 mode residential-bridge in-qos-prof-name nameQ0

//当使用双层vlan时创建SVLAN下的CVLAN
configure vlan id stacked:2000:[1001…1100] mode cross-connect in-qos-prof-name nameQ0
//或用configure vlan id stacked:2000:[1001…1100] mode residential-bridge in-qos-prof-name nameQ0


ONU数据业务配置
GPON
1、        注册ONU
typ:isadmin>#configure pon interface 1/1/8/8 auth-method sn-slid
//配置PON口认证模式

删除ONU
typ:isadmin># configure equipment ont interface 1/1/7/1/22 admin-state down
typ:isadmin># configure equipment ont
typ:isadmin>configure>equipment>ont# no interface 1/1/7/1/22


typ:isadmin>#info configure equipment ont interface                       
//可以现查看已配置的，避免ONUID冲突
typ:isadmin> # show pon unprovision-onu  //查看gpon未认证ONU
//注册ONT
typ:isadmin># configure equipment ont interface 1/1/8/8/5 sernum TDTC:35B3483A sw-ver-pland disabled voip-allowed enable

configure equipment ont slot 1/1/7/1/22/1 planned-card-type ethernet plndnumdataports 1 plndnumvoiceports 0 admin-state up

configure equipment ont slot 1/1/7/1/22/1 planned-card-type ethernet plndnumdataports 1 plndnumvoiceports 0 admin-state up

typ:isadmin># configure equipment ont slot 1/1/7/1/22/2 planned-card-type ethernet plndnumdataports 3 plndnumvoiceports 0 admin-state up


//SERNUM这一项必须在厂商标志（TDTC）后加冒号
typ:isadmin>configure>equipment>ont>interface>1/1/8/8/5$ admin-state up
typ:isadmin>configure>equipment>ont>interface>1/1/8/8/5$ exit all
typ:isadmin> show equipment ont interface           //查看GPON ONT装态
typ:isadmin>#
2、配置ont card（slot）、UNI及其qos
配置ont card（slot）
show equipment ont slot        //查看ont上报slot
configure equipment ont slot 1/1/8/8/5/1 planned-card-type 10_100base plndnumdataports 1 plndnumvoiceports 0 admin-state up       
配置ONU的UNI（网口）
configure interface port uni:1/1/8/8/5/1/[1…4] admin-up
typ:isadmin># configure interface port uni:1/1/7/1/22/1/1 admin-up


配置ONU的UNI（网口）上行速率

下行模板：
typ:isadmin># configure qos profiles shaper WS-MAX1G-D committed-info-rate 0 committed-burst-size 0 excess-info-rate 1024000 type singletokenbucketgpon

上行模板：
typ:isadmin># configure qos profiles bandwidth WS-MAX1G committed-info-rate 0 assured-info-rate 0 excessive-info-rate 1024000 delay-tolerance 8

configure qos interface 1/1/8/8/5/1/[1...4] upstream-queue 0 bandwidth-profile name:UPSTREAM_100M

typ:isadmin># configure qos interface 1/1/7/1/22/1/1 upstream-queue 0 bandwidth-profile name:WS-MAX1G

typ:isadmin># configure qos interface 1/1/7/1/22/2/1 upstream-queue 0 bandwidth-profile name:WS-MAX1G

typ:isadmin># configure qos interface 1/1/7/1/22/2/2 upstream-queue 0 bandwidth-profile name:WS-MAX1G

typ:isadmin># configure qos interface 1/1/7/1/22/2/3 upstream-queue 0 bandwidth-profile name:WS-MAX1G
typ:isadmin>configure>qos>interface>1/1/7/1/22/2/3>upstream-queue>0# exit all

show interface port         //查看port状态

3、svlan 2000配置到NT-A上联端口和lt板
//可用info configure service查看;若已配置无需重复配置。
configure service vpls 2000 customer 1 v-vpls vlan 2000 create
configure service vpls 2000 sap nt-a:xfp:2:2000 create
configure service vpls 2000 sap lt:1/1/8:2000 create
configure service vpls 2000 no shutdown


4、数据业务vlan应用到onu网口上,并把onu打上CLAN(pvid)
configure bridge port 1/1/8/8/5/1/[1…4]
//数据业务双层vlan应用到ONU
configure bridge port 1/1/8/8/5/1/[1...4] vlan-id stacked:2000:[1001...1004]
//configure bridge port 1/1/8/8/5/1/[1...4] max-unicast-mac 16
configure bridge port 1/1/8/8/5/1/[1...4] pvid [1001...1004]

//数据业务单层vlan应用到ONU
// configure bridge port 1/1/8/8/5/1/[1...4] vlan-id 2000 tag single-tagged
// configure bridge port 1/1/8/8/5/1/[1...4] pvid 2000








EPON
1、        注册ONU
//typ:isadmin>#configure epon interface 1/1/6/8 auth-mode mix
//配置PON口认证模式

typ:isadmin>#info configure equipment eont interface                       
//可以现查看已配置的，避免ONUID冲突
typ:isadmin>show epon unprovision-onu  //查看epon未认证ONU
//注册ONT
typ:isadmin>#configure equipment eont interface 1/1/6/8/1 mac-addr fc:b0:c4:1b:d7:88
typ:isadmin>configure>equipment>ont>interface>1/1/8/8/5$ admin-state up
typ:isadmin>configure>equipment>ont>interface>1/1/8/8/5$ exit all
typ:isadmin>show equipment eont interface          //查看EPON ONT装态
typ:isadmin>#

下面设置不是很清楚原理，用于SFU vlan自动协商时探测vlan的配置
typ:isadmin># configure equipment eont interface 1/1/6/8/1 port 1/1 vlanid-default 2000


2、配置ont 端口
注：Epon ont在OLT上不配置slot，默认只有slot 1，自动生成对应的euni和ellid，可用show interface port查看，将对应的euni和ellid admin-up。
configure interface port euni:1/1/6/8/1/1/1 admin-up
configure interface port ellid:1/1/6/8/1/1 admin-up

创建bridge port
configure bridge port 1/1/6/8/1/1
show interface port         //查看port状态


3、svlan 2000配置到NT-A上联端口和lt板
//可用info configure service查看
configure service vpls 2000 customer 1 v-vpls vlan 2000 create
configure service vpls 2000 sap nt-a:xfp:2:2000 create
configure service vpls 2000 sap lt:1/1/6:2000 create
configure service vpls 2000 no shutdown


4、数据业务vlan应用到onu网口上,并把onu打上CLAN(pvid)
//数据业务双层vlan应用到ONU
configure bridge port 1/1/6/8/1/1 vlan-id stacked:2000:[1001...1004]
//configure bridge port 1/1/6/8/1/1 max-unicast-mac 16
configure bridge port 1/1/6/8/1/1 pvid [1001...1004]

//数据业务单层vlan应用到ONU
// configure bridge port 1/1/6/8/1/1 vlan-id 2000 tag single-tagged
// configure bridge port 1/1/6/8/1/1 pvid 2000





ONU语音业务配置
GPON
1、注册ONU
typ:isadmin># configure equipment ont interface 1/1/8/8/5 sernum TDTC:35B3483A sw-ver-pland disabled voip-allowed enable

删除ONU
typ:isadmin># configure equipment ont interface 1/1/7/1/22 admin-state down
typ:isadmin># configure equipment ont
typ:isadmin>configure>equipment>ont# no interface 1/1/7/1/22


//需要配置语音业务时注册ONU必须添加voip-allowed enable，否则无法配置语音端口
typ:isadmin>configure>equipment>ont>interface>1/1/8/8/5$ admin-state up

2、配置ont card（slot）、qos
show equipment ont slot        //查看ont上报slot
configure equipment ont slot 1/1/8/8/5/2 planned-card-type pots plndnumdataports 0 plndnumvoiceports 2

configure qos interface 1/1/8/8/5/voip upstream-queue 0 priority 8 bandwidth-profile name: UPSTREAM_100M        //也可用默认的语音上行模版“1_1_voip”

3、svlan 45配置到NT-A上联端口和lt板
configure service vpls 45 customer 1 v-vpls vlan 45 create
configure service vpls 666 sap nt-a:xfp:2:666 create
configure service vpls 666 sap lt:1/1/7:666 create
configure service vpls 666 no shutdown



4、语音业务vlan应用到onu voip口上,并打上CLAN(pvid)
configure bridge port 1/1/8/8/5/1/1 vlan-id 45
//此处语音vlan下发后语音业务才通，但为什么要下发此处不太清楚

创建语音端口bridge port
configure bridge port 1/1/8/8/5/voip
语音vlan应用到语音端口
configure bridge port 1/1/8/8/5/voip vlan-id 45   
configure bridge port 1/1/8/8/5/voip pvid 45

5、在ONU上做语音业务相关配置（略）

EPON
1、注册ONU
typ:isadmin>#configure equipment eont interface 1/1/6/8/1 mac-addr fc:b0:c4:1b:d7:88

2、配置ont 端口
configure bridge port 1/1/6/8/1/1

3、svlan 45配置到NT-A上联端口和lt板
configure service vpls 45 customer 1 v-vpls vlan 45 create
configure service vpls 45 sap nt-a:xfp:2:45 create
configure service vpls 45 sap lt:1/1/6:45 create
configure service vpls 45 no shutdown

4、语音业务vlan应用到onu上
configure bridge port 1/1/6/8/1/1 vlan-id 45

5、贝尔OLT组播配置
第一步：创建组播vlan
configure vlan id 1010 mode residential-bridge in-qos-prof-name nameQ0
第二步：配置组播vlan，并绑定到相应上联端口和LT板卡
configure service vpls 1010 customer 1 v-vpls vlan 1010 create
configure service vpls 1010 no shutdown
configure service vpls 1010 sap lt:1/1/7:1010 create
configure service vpls 1010 sap nt-a:xfp:1:1010 create
configure service vpls 666 sap nt-a:xfp:2:0 create

configure service vpls 2000 customer 1 v-vpls vlan 2000 create
configure service vpls 2000 sap nt-a:xfp:2:2000 create
configure service vpls 2000 sap lt:1/1/8:2000 create
configure service vpls 2000 no shutdown

configure service vpls 668 customer 1 v-vpls vlan 668 create
configure service vpls 668 sap nt-a:xfp:2:0 create
configure service vpls 668 sap lt:1/1/7:668 create
configure service vpls 668 no shutdown

configure service vpls 1991 customer 1 v-vpls vlan 1991 create
configure service vpls 1991 sap nt-a:xfp:2:1991 create
configure service vpls 1991 sap lt:1/1/7:1991 create
configure service vpls 1991 no shutdown
configure vlan id 1991 ipv4-mcast-ctrl ipv6-mcast-ctrl mac-mcast-ctrl new-broadcast enable in-qos-prof-name name:PQ0 mode residential-bridge
configure vlan id 1991 unknown-unicast
configure bridge port 1/1/7/1/3/1/1 vlan-id 1991 tag single-tagged

configure service vpls 1992 customer 1 v-vpls vlan 1992 create
configure service vpls 1992 sap nt-a:xfp:2:1992 create
configure service vpls 1992 sap lt:1/1/7:1992 create
configure service vpls 1992 no shutdown
configure vlan id 1992 ipv4-mcast-ctrl ipv6-mcast-ctrl mac-mcast-ctrl new-broadcast enable in-qos-prof-name name:PQ0 mode residential-bridge
configure vlan id 1992 unknown-unicast
configure bridge port 1/1/7/1/3/1/1 vlan-id 1992 tag single-tagged

configure service vpls 1993 customer 1 v-vpls vlan 1993 create
configure service vpls 1993 sap nt-a:xfp:2:1993 create
configure service vpls 1993 sap lt:1/1/7:1993 create
configure service vpls 1993 no shutdown
configure vlan id 1993 ipv4-mcast-ctrl ipv6-mcast-ctrl mac-mcast-ctrl new-broadcast enable in-qos-prof-name name:PQ0 mode residential-bridge
configure vlan id 1993 unknown-unicast
configure bridge port 1/1/7/1/22/1/1 vlan-id 1993 tag single-tagged


第三步：打开系统组播功能，并设置IGMP版本为V2
configure igmp system start  
configure igmp system netw-igmp-version 2  
configure igmp system user-igmp-version 2  
第四步：设置禁用CAC
configure qos cac-mode nocac  
第五步：配置组播源地址
configure mcast channel 239.1.1.1 src-ip-addr 0.0.0.0 vlan-id 1010 peak-bit-rate 100000  
第六步：配置用户端口组播channel
Configure igmp channel channel vlan:1/1/7/1/5/1/1:1010 max-num-group 10 igmp-version system-inherited






6、在ONU上做语音业务相关配置（略）

附录：常用查看命令
The ‘pon or ont ***’ cmd is used for GPON, and the ‘epon or eont***’ cmd is used for EPON
show equipment slot 查看设备
show port 显示上联口装态及配置信息
show interface port 查看ONU ，UNI口，bridge-port ,PON口装态。
show pon unprovision-onu  //查看gpon未认证ONU
show equipment ont interface  查看ONU装态
show service fdb-mac 查看学习到的MAC（可查看上下联MAC地址）
show vlan fdb-board   查看PON上学到的MAC
show vlan bridge-port-fdb 查看bridge-port学到的MAC地址（可以用来查看某一ONU的某一业务的MAC）
show pon optics 查看PON光功率
show equipment ont optics 查看ONU的收发光功，电压温度。
以上是7360常用查看命令


下面是显示配置命令
info configure equipment slot 显示硬件配置信息
info configure pon interface   显示 PON口配置信息（ONU注册方式及是否打开。）

info configure equipment ont interface <LOID>  显示所有ONU配置信息要，（也可以在后面加入具体的ONU位置查看某一个ONU）   
例如：
info configure equipment ont interface 1/1/1/2/3      
查看第1块PON板第2个PON口的第3个ONU配置信息
info configure equipment ont slot 显示ONU 的ONUCARD信息  
上面部分可以用下面的命令可以一次全部查看
info configure equipment ont   

info configure interface port   显示UNI口信息及PON是否打开（有admin-up 为打开）
info configure qos profiles bandwidth  
显示上行带宽模板
info configure qos profiles shaper      
显示下行带宽模板  
configure qos interface 1/1/1/2/23/14/1 scheduler-node nameN_100M info configure service id
显示所有VLAN绑定信息         
info configure vlan id     显示VLAN信息
info configure bridge port   显示bridge port 信息  
show equipment ont interface 查看猫的序列号和版本编号
admin equipment ont interface 1/1/8/8/12 reboot        重启ONU

typ:isadmin># show port nt-a:xfp:2